Installation · NN300 · HMI

Commissioning chapter from NN300-ICM-001. Press Set Length and Set Width after every value change or the mechanism will not move.

NN300 Installation

HMI Length & Width Commissioning

Target running clearance is approximately 0.5 mm. Adjust in 0.1 mm steps and re-confirm with Set Length / Set Width.

← NN300 Installation & Commissioning Guide

Length and width entry

Open Parameter Adjustment or Length/Width Adjustment from the bottom navigation bar.

Press Reset on each column before entry
Enter length (mm) and width values — Width 1 and Width 2 identical for square frames
Press Set Length and Set Width to confirm each change
Wait for mechanism to stop before reaching into the station

NN300 HMI length width entry — Fig. 10 — Parameter entry

NN300 Set Length Set Width buttons — Fig. 11 — Confirm buttons

Clearance check (~0.5 mm)

Place moulding display-face up. Slide left/right with light finger pressure — no binding, no excessive play.

If too tight, increase values in 0.1 mm steps; if too loose, decrease
Press Set Length or Set Width after each adjustment
Verify both length and width directions before nailing setup

NN300 moulding clearance check — Fig. 12 — Clearance check

Nailing row configuration

On the Automatic Screen, set Distance (up to 10 rows) and Nail Count per row. Match Row 1 and Row 2 to physical nail exits.

Trial-nail one piece before batch production
Press Reset on Automatic Screen when setup is complete

NN300 nailing row HMI — Fig. 13 — Row spacing & count

NN300 physical nail exits — Fig. 14 — Physical reference

NN300 default operating state — Fig. 17 — Default state

HMI commissioning FAQ

Why must I press Set Length / Set Width after every change?

The XINJE HMI only commands axis motion after confirmation. Without it, clearance checks and nailing setup will be invalid.

What clearance should I target?

Approximately 0.5 mm running clearance. Too tight causes nail misalignment; too loose affects positioning accuracy.

Next: trial run

Continue the NN300 guide

Full manual

Length and width entry

Open Parameter Adjustment or Length/Width Adjustment from the bottom navigation bar.

Press Reset on each column before entry

Enter length (mm) and width values — Width 1 and Width 2 identical for square frames

Press Set Length and Set Width to confirm each change

Wait for mechanism to stop before reaching into the station

Fig. 10 — Parameter entry

Fig. 11 — Confirm buttons

Clearance check (~0.5 mm)

Place moulding display-face up. Slide left/right with light finger pressure — no binding, no excessive play.

If too tight, increase values in 0.1 mm steps; if too loose, decrease

Press Set Length or Set Width after each adjustment

Verify both length and width directions before nailing setup

Fig. 12 — Clearance check

Nailing row configuration

On the Automatic Screen, set Distance (up to 10 rows) and Nail Count per row. Match Row 1 and Row 2 to physical nail exits.

Trial-nail one piece before batch production

Press Reset on Automatic Screen when setup is complete

Fig. 13 — Row spacing & count

Fig. 14 — Physical reference

Fig. 17 — Default state

HMI commissioning FAQ

Why must I press Set Length / Set Width after every change?

The XINJE HMI only commands axis motion after confirmation. Without it, clearance checks and nailing setup will be invalid.

What clearance should I target?

Approximately 0.5 mm running clearance. Too tight causes nail misalignment; too loose affects positioning accuracy.

Length and width entry

Clearance check (~0.5 mm)

Nailing row configuration

HMI commissioning FAQ

Continue the NN300 guide

Full manual

Productos destacados

Explorar XKY

Insights semanales sobre maquinaria industrial para enmarcado

Length and width entry

Clearance check (~0.5 mm)

Nailing row configuration

HMI commissioning FAQ

Continue the NN300 guide

Full manual

Productos destacados

Explorar XKY

Insights semanales sobre maquinaria industrial para enmarcado