安装 · NN300 · HMI

每次修改数值后必须按 Set Length / Set Width 确认，否则机构不会动作。

NN300 安装

HMI 长宽调试

目标运行间隙约 0.5 mm。过紧或过松均以 0.1 mm 步进微调并重新确认。

← NN300 安装与调试指南

长宽输入

Open Parameter Adjustment or Length/Width Adjustment from the bottom navigation bar.

Press Reset on each column before entry
Enter length (mm) and width values — Width 1 and Width 2 identical for square frames
Press Set Length and Set Width to confirm each change
Wait for mechanism to stop before reaching into the station

NN300 HMI length width entry — Fig. 10 — Parameter entry

NN300 Set Length Set Width buttons — Fig. 11 — Confirm buttons

间隙检查（约 0.5 mm）

Place moulding display-face up. Slide left/right with light finger pressure — no binding, no excessive play.

If too tight, increase values in 0.1 mm steps; if too loose, decrease
Press Set Length or Set Width after each adjustment
Verify both length and width directions before nailing setup

NN300 moulding clearance check — Fig. 12 — Clearance check

打钉行配置

On the Automatic Screen, set Distance (up to 10 rows) and Nail Count per row. Match Row 1 and Row 2 to physical nail exits.

Trial-nail one piece before batch production
Press Reset on Automatic Screen when setup is complete

NN300 nailing row HMI — Fig. 13 — Row spacing & count

NN300 physical nail exits — Fig. 14 — Physical reference

NN300 default operating state — Fig. 17 — Default state

HMI 调试 FAQ

为什么每次改数都要按 Set Length / Set Width？

信捷 HMI 仅在确认后才驱动轴运动，否则间隙检查与打钉设置无效。

间隙应调到多少？

约 0.5 mm。过紧易打钉偏位，过松影响定位精度。

下一步：试机验收

继续阅读

完整手册

长宽输入

Open Parameter Adjustment or Length/Width Adjustment from the bottom navigation bar.

Press Reset on each column before entry

Enter length (mm) and width values — Width 1 and Width 2 identical for square frames

Press Set Length and Set Width to confirm each change

Wait for mechanism to stop before reaching into the station

Fig. 10 — Parameter entry

Fig. 11 — Confirm buttons

间隙检查（约 0.5 mm）

Place moulding display-face up. Slide left/right with light finger pressure — no binding, no excessive play.

If too tight, increase values in 0.1 mm steps; if too loose, decrease

Press Set Length or Set Width after each adjustment

Verify both length and width directions before nailing setup

Fig. 12 — Clearance check

打钉行配置

On the Automatic Screen, set Distance (up to 10 rows) and Nail Count per row. Match Row 1 and Row 2 to physical nail exits.

Trial-nail one piece before batch production

Press Reset on Automatic Screen when setup is complete

Fig. 13 — Row spacing & count

Fig. 14 — Physical reference

Fig. 17 — Default state

长宽输入

间隙检查（约 0.5 mm）

打钉行配置

HMI 调试 FAQ

继续阅读

完整手册

相关产品

探索新框源

每周装裱设备行业洞察

长宽输入

间隙检查（约 0.5 mm）

打钉行配置

HMI 调试 FAQ

继续阅读

完整手册

相关产品

探索新框源

每周装裱设备行业洞察